SpeedyBee F405 WING APP Fixed Wing Flight Controller

F405 board for wings/planes. One of its great features is the capability to wirelessly connect to your configurator via BLE, classic Bluetooth and Wi-Fi.

Features:

• Wireless configuration (BLE, Bluetooth, Wifi) via the SpeedyBee app and QGroundcontrol app.
• Easy installation with connector plugs for all of your gear
• Supports INAV and Ardupilot (including Ardupilot's VTOL function)
• CRSF telemetry data displayed by LUA script
• On board 4 level battery life indicator
• On board current sensor with 3 BEC outputs
• 6 UARTs available
• Up to 11 PWM outputs
• Switch available to mute your buzzer while configuring

Specifications:

• FC:
  • MCU: STM32F405,168MHz,1MB Flash
  • IMU (Gyro & Accelerometer): ICM-42688-P
  • Barometer: SPL006-001
  • OSD chip: AT7456E
  • Blackbox: MicroSD Card Slot
  • UARTs: 6 sets - Note that UART6 is dedicated for the wireless board telemetry connection
  • I2C: 1x Used for magnetometer, digital airspeed sensor
  • ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed)
  • PWM: 12x (11+1“LED”pad)
  • ELRS/CRSF receiver: Supported, use UART1
  • SBUS: Built in inverter for SBUS input (UART2-RX)
  • LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB
  • RSSI: Supported, named as RS
  • Supported FC Firmware: INAV:SpeedyBeeF405WING (default) / ArduPilot: SpeedyBeeF405WING
  • Weight: 8.9g
     
• PDB board:
  • Input voltage range: 7~36V (2~6S LiPo)
  • Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot)
  • Battery Current Sensor: 90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot)
  • TVS Protective diode: Yes
  • FC BEC output:
    Output 5.2V +/- 0.1V DC continuous current 2.4 Amps
    3A Peak designed for FC, receiver, GPS module, airSpeed module, telemetry module, WS2812 LED_Strip
  • VTX BEC output:
    Output 9V +/- 0.1V DC Continuous current 1.8 Amps
    2.3A Peak voltage adjustable, 9V Default, 12V or 5V via jumper designed for analog video transmitter, digital video transmitter and camera.
  • Servo BEC output: Output 4.9V +/- 0.1V DC continuous current 4.5 Amps, 5.5A peak voltage adjustable, 4.9V default, 6V or 7.2V via jumper designed for servos.
  • Weight: 11.4g
     
• Wireless board:
  • Wireless Configuration (long press BOOT button for 6 seconds to switch modes):
    BLE mode, connect to Speedybee APP
    Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.
    Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner
  • LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes):
    4x WS2812 LED strip connectors, adjustable colors and flashing modes
    Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads
  • On-board battery level indicator: 4x RGB indicator LED for battery level display by number of lights
  • Weight: 4.2g

Package:

• 1x F405 WING FC board
• 1x PDB board
• 1x Wireless board
• 1x USB extender
• 1x 3x12 90 degree pin header
• 3x 1x12 straight pin header
• 1x 1x4 straight pin header
• 5x M2x12 copper standoff spacer
• 10x M2x4 small head cross screws
• 5x M3x4 silicone grommets
• 1x 8pin SH1.0 USB extender cable (80mm)
• 1x 4pin SH1.0 analog VTX cable (250mm)
• 1x 6pin SH1.0 GPS module cable without connector on the other end (250mm)
• 1x 6pin digital VTX cable (250mm)
• 1x 4pin SH1.0 to 3+2pin JST1.25 FPV cam cable(250mm)
• 1x 6pin GH1.25 telemetry module cable(200mm)
• 1x 4pin Dupont single-head cable(150mm)
• 1x Double-sided tape for isolating pins and cables (32×9x1mm)

Manual here

Write a review