SpeedyBee F7 V3 BL32 50A Stack

SpeedyBee F7 V3 BL32 50A Stack
SpeedyBee F7 V3 BL32 50A Stack
×
Brand: SpeedyBee
Product Code: SB-Stack-F7V3-50A
Availability: Out Of Stock
Price: CAD$165.60
Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product
Description Reviews (0) Related Products (4)

F7 V3 flight controller + 50A ESC with Bluetooth and WiFi capability allowing you to wirelessly flash, change settings, tune and even analyze your blackbox.

Features:

FC Specifications:

MCU STM32F722
IMU(Gyro) BMI270
USB Port Type Type-C
Barometer BMP280
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used for Flight Controller configuration
Flash FC Firmware Wirelessly Supported. Please enter MENU > FC Firmware Flasher
Download/Analyze Blackbox Supported. Please enter MENU > Blackbox Analyzer
DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
Flash (for BlackBox) 500MB
BetaFlight Camera Control Pad Yes (CC pad on the front side)
Power Input 3S - 6S LiPo
5V Output 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) - Top side.
6x +5V output via the connectors - Bottom side.
The total current load is 2A.
9V Output 1x +9V pad - Top side
1x +9V pad via connector - Bottom side.
The total current load is 4A.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for receiver and GPS module (can be powered via USB).
Up to 1A current load.
ESC Signal Pads M1 - M4 on bottom side and M5-M8 on top side.
UART 5 sets(UART1, UART2, UART3, UART4 (For ESC Telemetry), UART6
ESC Telemetry UART R4 (UART4)
I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc...
LED Pad Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input Supported. Named as RS on the front side.
SmartPort Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller Firmware BetaFlight(Default), EMUFlight, INAV
Firmware Target Name SPEEDYBEEF7V3
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 41(L) x 38(W) x 8.1(H)mm
Weight 10.7g

 
ESC Specifications:

Continuous Current 50A * 4
Burst Current 55A(5S)
TVS Protective diode Yes
Heat Sink Yes
External Capacitor 1500uF Low ESR Capacitor (Included)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=490 Offset=0)
Mounting 30.5 x 30.5mm (4mm hole diameter)
Dimension 45.6(L) * 40(W) * 8.8mm(H)
Weight 19.2g with heat sink
Firmware SpeedyBee BL32 50A


Package:

Manual here

Write a review

Please Login To Review This Product
Related