Ready-To-Build Micro Brushless Whoop kit

Ready-To-Build Micro Brushless Whoop kit
Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit Ready-To-Build Micro Brushless Whoop kit
Brand: Rotorgeeks
Product Code: RTB Micro Brushless Whoop kit
Availability: In Stock
Price: USD$99.99

Available Options


* Prop color:






* Frame:

* Receiver:

Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

Build your own Brushless 1S whoop!  This kit contains everything you need to build a 1S Micro Brushless quad with a 65mm frame and comes with 2 FREE GNB250mAH HV Lipos.
FrSky and DSM Compatible only.  D8 Mode is recommended for the FrSky Receiver.

Specifications:

Flight Controller:

  • HappyModel Crazybee F3 flight controller FrSky Version
  • Firmware: Betaflight_3.3.0_Crazybee
  • MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
  • Sensor: MPU-6000 (SPI connection)
  • Power supply: 1S battery input (DC 3.5-4.35V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Frsky version Built-in SPI control Frsky receiver with telemetry(D8/D16 switchable)
  • DSM2/X version Built-in Serial-based Spektrum compatible DSM2/DSMX satellite receiver
  • Built-in Betaflight OSD(SPI Controll)
  • Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
  • Built-in 5V 0.8A BEC with LC filter
  • Built-in voltage detection
  • BLHELI pass-through Ready
  • Heading LED Ready
  • Board size: 28.5 * 28.5MM
  • Board weight: 3.5 g

Rotorgeeks Tip: The Flight Controller comes with tall rubber dampers - cut them down for use on the canopy sides or the screw won't catch on the post.

ESC parameters:

  • Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: O_L_5_REV16_7.HEX
  • Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM

Brushless Motor:

  • HappyModel SE0603 19000kv Brushless Motor:
  • KV: 19000KV
  • Shaft Diameter: 0.8mm
  • Configuration: 9N12P
  • Stator Diameter: 6mm
  • Stator Length: 3mm
  • Motor Dimension(Dia.*Len): Φ9mm*15.4mm
  • Terminals: JST1.25mm
  • No.of Cells(Lipo): 1S
  • Wire length(include connector): 35mm
  • Weight: 1.7g
  • Double E-clip design, prevent Motor bell to flying off
  • Good Dynamic balance

Camera/VTX:

  • HappyModel HCF9
  • Output power: 25mw
  • Frequency: 48CH
  • Input voltage: 3.3V 5.5V
  • Current consumption: 300mA(type)
  • Camera resolution: 700TVL
  • Field of view: 120°
  • Video Format: NTSC
  • Antenna: RG178 antenna
  • Frequency: 5.8GHz 6 bands 48 channels
  • With Raceband: 5474 5945 MHZ
  • Size: 13.9″12.0mm ( L*W )
  • Weight: 3g
  • Frequency switching: By one button, Short press the button to change channel, 1-8 adjustable.
  • Press and hold the button for 2s to change bands, 1-6 adjustable

Note: See picture to properly mount the camera onto the camera mount

Frame:

  • BWhoop65 65mm Brushless
  • Color option: White, Lemon, Green
  • Weight: 3g

Canopy:

  • HappyModel Snapper6/7
  • Material: ABS
  • Weight: 1.5g

Props:

  • 31mm 4-Blade Micro Props
  • Material: ABS
  • Weight: 1.5g

Write a review

Please Login To Review This Product

Rotorgeeks © 2019
View Mobile / Standard