HappyModel Mobula7 HD BNF

HappyModel Mobula7 HD BNF
HappyModel Mobula7 HD BNF HappyModel Mobula7 HD BNF HappyModel Mobula7 HD BNF HappyModel Mobula7 HD BNF
Brand: HappyModel
Product Code: Mobula7 HD
Availability: Out Of Stock
Price: USD$149.00

Available Options

* Batteries:

* Receiver:

Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

Please note we have stopped carrying this model due to high failure rates.
HappyModel is stepping up their game with the introduction of the new CineWhoop Mobula7 HD 2-3S.


  • For FrsKY users we recommend using the D8 protocol.  This receiver uses SPI RX and there have been issues with the Betaflight D16 code.
  • You will notice that some wires are too close to the front left prop. We recommend twisting the wires and tuck them away from the prop.
  • If you are using 3S HV batteries, HappyModel suggests to set the throttle to 75%-80% to avoid the FETs from burning. The problem doesn't occure with regular 3S or 2S batteries.


  • New Crazybee F4 PRO V2.0 AIO Flight controller 1-3s Lipo Compatible
  • 2S suited for indoor Cinewhoop flight
  • 3S suited for outdoor freestyle flight
  • Betaflight support
  • Multi flight mode: ACRO/AIR/ANGLE
  • The lightest 1102 brushless motor only 2.7g with double ball bearings
  • Betaflight OSD support , with RSSI, Voltage ,current from your goggles (DSMX version has no RSSI output)
  • Caddx turtle v2 + 1080p 60fps DVR ready (Does not come with an SD card)
  • Camera angle adjustable
  • VTX power switchable: 25mw~200mw
  • Smartaudio ready
  • Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
  • Full telemetry function ready (Frsky Non-EU)
  • Special Breath light ready
  • BNF
  • Compatible both for 2s-3s Lipo/LIHV

Note: Although the Flight Controller is 1S-3S capable the Mobula7 HD will only fly with 2S or 3S batteries.


  • Wheelbase: 75mm
  • Size: 98mm*98mm*45mm
  • Weight: 48g(without battery)
  • Weight:72g (with Original 3s 300mah Lipo battery)


  • Mode: EX1102 KV10000
  • Configuration:9N12P
  • Stator Diameter:11mm
  • Stator Length:2mm
  • Shaft Diameter:Φ1mm
  • Motor Dimension (Dia.*Len):Φ13.5mm*16mm
  • Weight(g):2.8g
  • Can take 1S-3S LiPo battery

Flight Controller:

  • (Frsky version) CRAZYBEE F4FR PRO V2.0 Firmware target: CrazybeeF4FR
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1-3S battery input (DC 3.5-13V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
  • Built-in Betaflight OSD(SPI Control)
  • Built-in Current meter Max 28A
  • Current meter scale set to 1175
  • Built-in 5V 1A Buck / Boost with LC filter
  • Built-in voltage detection

Onboard 4in1 ESC:

  • MCU upgraded to EFM8BB21
  • Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
  • Current: 5A continuous peak 6A (5 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_50_REV16_7.Hex
  • Default protocol: DSHOT600

Frsky NON-EU receiver Version:

  • SPI BUS receiver
  • Frsky D8/D16 switchable
  • Compatible Non EU transmitter both D8 and D16 mode
  • 8ch or 16ch
  • Failsafe support
  • No ground interference ( Transmitter and receiver 1 m from the ground): 300m


  • Output power: 25~200mw switchable
  • Frequency: 40CH
  • Input voltage: 3.3V 5.5V
  • Current consumption: 300mA(type)
  • Antenna: RG178 antenna
  • Frequency: 5.8GHz 5bands 40 channels
  • With Raceband
  • Smartaudio ready
  • Weight: 3g

CADDX Turtle V2:

  • Image sensor: 1/2.7″ CMOS sensor
  • Horizontal: 800TVL
  • TV system: NTSC/PAL switchable
  • Video Resolution: [email protected] / [email protected] / [email protected]
  • Power Input: DC 4.5-20V
  • FPV FOV: 155°
  • Recording FOV: 170°
  • Mini Illumination: 0.01lux
  • Image Resolution: 2 Megapixels
  • Lens: 1.8mm Turbo Eye Lens
  • Working Current: [email protected]/[email protected] (low consumption)
  • OSD Menu: Yes (Support Voltage Display)
  • Video Files: MP4
  • Audio: Support
  • Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100
  • S/N Ratio: >60dB (AGC OFF)
  • Video Output: CVBS
  • Max Micro SD Card Supported: 8-64GB (need Class 10 or above, recommend Class 10/UHS-I/UHS-II)
  • Color: Red

Lipo Battery:

  • Capacity:300mAh
  • Voltage:11.4v
  • Continuous Discharge Rate: 30C
  • Instantaneous discharge rate: 60C
  • Size: 65mmx18mmx11mm
  • Weight: 23g
  • Connector: XT30

Package includes:

  • 1x Mobula7 HD
  • 1x Extra set of HQ 1.6x1.6x4 (40mm propeller) (2cw+2ccw)
  • 1x 3S 11.4v 300mah 30C/60C battery
  • 1x Propeller disassemble tool
  • 1x Screwdriver & screws
  • 1x XT30 to 2x PH2.0 connector adapter (so you can use 2x 1S battery in series like the Mobula7 V2 BNF)
  • 1x Control board for the Caddx Turtle V2
  • 1x Manual

Recommended Batteries:

  • GNB 2S 350 HV
  • GNB 2S 300 HV
  • GNB 3S 300HV

FrSky manual here
Firmware updates for the Caddx Turtle V2 here

Please note that all warranty claims are handled and approved by Happy Model only.  If you have any issues please contact them here

Write a review

Please Login To Review This Product

Rotorgeeks © 2019
View Mobile / Standard