HappyModel Mobula6 1S Brushless Regular Edition BNF - FrSky (no batteries)

HappyModel Mobula6 1S Brushless Regular Edition BNF - FrSky (no batteries)
HappyModel Mobula6 1S Brushless Regular Edition BNF - FrSky (no batteries) HappyModel Mobula6 1S Brushless Regular Edition BNF - FrSky (no batteries) HappyModel Mobula6 1S Brushless Regular Edition BNF - FrSky (no batteries)
Brand: HappyModel
Product Code: Mobula6 Regular FrSky
Availability: In Stock
Price: CAD$138.60

Available Options


Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

An ultra light 1S brushless whoop.
Please note this version does not include any batteries.


  • For FrsKY users we recommend using the D8 protocol.  This receiver uses SPI RX and there have been issues with the Betaflight D16 code.
  • The switch on the USB charger is for regular or HV battery charge:
    - Switch towards the battery plugs - regular lipo charge
    - Switch towards the usb connectior - HV lipo charge


  • AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
  • Extreme light 1S 65mm Brushless whoop only 20g
  • Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
  • Smooth and powerful
  • Compatible for 1S Lipo/LIHV
  • Camera Angle adjustable
  • Receiver: internal SPI Frsky version (Compatible with ACCST D8/D16, we recommend using D8 mode)
  • Motor: SE0802 KV19000 (Regular Edition)


  • Wheelbase: 65mm
  • Size: 80mm*80mm*37mm
  • Weight: 20g

Flight controller:

  • CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1S battery input (DC 2.9V-4.35V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Built-in Betaflight OSD (SPI Control)
  • Built-in 5.8G VTX
  • Built-in SPI Frsky receiver
  • Built-in 5V 1A BEC
  • Built-in voltage detection

Onboard 4in1 ESC:

  • MCU upgraded to EFM8BB21
  • Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: O_H_5_REV16_7.HEX
  • Default protocol: DSHOT600

Onboard Frsky SPI D8 receiver Version:

  • SPI BUS receiver Frsky D8 compatible
  • Compatible Non EU transmitter D8 modelChannels: 8ch
  • Failsafe support
  • No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m

Onboard 5.8g VTX:

  • Output power: 25mw
  • Frequency: 40CH
  • Input voltage: 3.3V 5.5V
  • Current consumption: 300mA(type)
  • Frequency: 5.8GHz 5bands 40 channels
  • With Race band
  • Smartaudio ready

Runcam Nano3:

  • Model: RunCam Nano 3
  • Image Sensor: 1/3″ CMOS
  • Horizontal Resolution: 800TVL
  • Lens : 2.1mm(M8) FOV 160°
  • Signal System: NTSC
  • S/N Ratio: >50dBElectronic Shutter Speed: Auto
  • Auto Gain Control (AGC): Auto
  • Min. Illumination: [email protected]
  • D-WDR: Auto
  • Day/Night: Color
  • Power:DC 3-5.5V
  • Current: [email protected] [email protected]
  • Housing Material: ABS
  • Net Weight: 1.2g
  • Dimensions: L14mm*W14mm*H9mm


  • SE0802 19000KV
  • Configu-ration:9N12P
  • Stator Diamter:8mm
  • Stator Length:2mm
  • Shaft Diameter:Φ1mm
  • Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
  • Weight(g):1.9g
  • No.of Cells(Lipo):1S only


  • Gemfan 1219-3
  • Center Thickness:5mm
  • Prop Disk Diameter:31mm
  • Center Hole Inner diameter:1.0mm
  • Weight:0.28g


  • 1x Mobula6 1S 65mm whoop Drone Frame
  • 1x Extra Gemfan 1219-3 Propellers (2cw+2ccw)    
  • 1x 1S Lipo/LIHV USB Charger
  • 1x Propeller disassemble tool

The only battery that fits this quad is the cabled version of the GNB 1S 380mAh or the cabled GNB 1S 350mAhBatteries with plugs directly on the end don't work because the cable isn't long enough. 
Manual here
Requires an older version of Betaflight configurator 10.4.0

Please note that warranty claims are handled and approved by Happy Model..  If you have any issues please contact them here

Write a review

Please Login To Review This Product