HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX

HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX
HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX
Brand: HappyModel
Product Code: 2E30027
Availability: In Stock
Price: USD$41.99
Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

A further updated version of the all in one flight controller from HappyModel. It is a single board providing an F4 processor with MPU6000 gyro, OSD, built-in DSM2/X receiver and four 5A ESCs.  We have attempted to capture and explain the changes to each revision below.

 V2.0 changes

  • 3S capable (FETs changed)
  • bind and boot buttons changed to larger size for convenience
  • main power pads changed to through-hole for better physical connection
Flight Controller
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1-3S battery input (DC 3.5-13V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • ESC MCU Upgraded to EFM8BB21
  • DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver)
  • Dsm2/DSMX, Ibus protocol etc.
  • Built-in Betaflight OSD (SPI Control)
  • Built-in Current meter sensor Max up to 28A
  • Current meter scale set to 1175
  • Built-in 5V 1A Buck / Boost with LC filter
  • Built-in voltage detection
  • BLHELI_S pass-through Ready
  • Multi Serial port support
  • Fully compatible with almost Brushless whoop drone
  • Weight:4.2g
Onboard 4in1 ESC
  • MCU upgraded to EFM8BB21
  • Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_50_REV16_7.Hex
  • Default protocol: DSHOT600


Package:

  • 1x Crazybee F4 PRO V2.1 flight controller
  • 3x Power cables
  • 1x set Shock absorbing rubber and screws

Firmware updates here
DSMX manual here

Note from HappyModel:

Due to many complaints about upgrading the PH2.0 to XT30 causing the MOSFET to burn, it is now recommended to use an XT30 with a capacitor (ESR less than 0.2 ohm and a capacitance of more than 100uF).
With the Capacitor , you can use 3S 300~350mah battery for the Crazybee F4 PRO V2.0 and Crazybee F4 PRO V2.1 , and 2s 300~350mah battery for the Crazybee F4 PRO V1.0 And if you want to use the battery above 350mah , we recommend using a 220uF capacitor or above.

Write a review

Please Login To Review This Product

Rotorgeeks © 2019
View Mobile / Standard