Rotorgeeks SSD F3 control board

Rotorgeeks SSD F3 control board
Rotorgeeks SSD F3 control board Rotorgeeks SSD F3 control board Rotorgeeks SSD F3 control board Rotorgeeks SSD F3 control board Rotorgeeks SSD F3 control board
Brand: Rotorgeeks
Product Code: RG SSD
Availability: Out Of Stock
Price: USD$29.99

Available Options


Qty:     - OR -   Add to Wish List
Add to Compare
11 reviews  11 reviews  |  Please Login To Review This Product

The Rotorgeeks SSD is an F3 based flight controller with best-in-class components, an intelligent layout and a great price.   While most flight controllers are derived from the old Naze 32 architecture, the SSD was designed from the ground up using the larger 64 pin package allowing 5 serial ports and other flexibility.  This fresh pinout architecture also means DSHOT ESC protocol is supported without sacrificing any features, using supplemental code to remap resources, pin swapping or jumpers.

The must haves

  • Invensense MPU 6000 IMU connected through SPI for maximum read speeds
  • Direct battery connection up to 6S with reverse polarity protection
  • Side mounted Blackbox MicroSD card slot connected via SPI for maximum write speeds and easy transfer (by removing card)
  • A layout that makes sense and keeps a build tight even when using headers pins and connectors
  • High current 5V supply – ability to power the control board, receiver, addressable LEDs, 5V vtx etc.  Can deliver steady 1.5A @ 6S input (more at lower battery power)
  • All solder points are through-hole and spaced away from critical surface mount components
  • NO fragile micro pitch connectors

Key features

  • DSHOT supported – no jumpers, remapping etc.
  • Low profile onboard IR leds to interface with IR based lap timing systems – one on each side covers any gate setup (code tbd)
  • Receiver / satellite function with USB power – no need for main battery to do binding and setup (safer too!)
  • Huge 5V supply to provide power for receiver, addressable LEDs, and other devices including high consumption 5V video transmitters (actual voltage is 5.06V)
  • Full telemetry support including SmartPort
  • One common input for serial Rx and PPM receivers
  • Direct satellite support for Spektrum users including 3.3V supply and binding functionality.  No need to pre-bind with a receiver anymore.
  • 6 PWM outputs so you can run a hexacopter, gimbal or other PWM controlled devices like switches etc.
  • BLHeli passthrough supported
  • Single sided design – just the sd slot on the bottom, low profile, easy to work with and reliable
  • Switched ground buzzer pin lets you connect to battery for extra loud beeping
  • USB VCP – firmware flashing without using bootloader pins
  • Voltage monitoring (and current with external sensor)
  • Runs on Betaflight firmware

36x36mm board, 30.5 mounting holes
Weight 6.25g
Current batch of boards is Blue and has conformal coating on the top for moisture protection

Manual available here

RCGroups thread here

Setup Notes
Connecting and flashing use different drivers

Windows 10 users should be able to connect without any driver install.
Windows 7 and older, if you don't see your board as a com port, download drivers here
To connect with the EZ-GUI Ground Station Android app, use Driver 1 (in settings), at default baud rate of 115,200

For All Windows users (1st time only if you haven't previously used a VCP F3 board on the pc)
When flashing new firmware the board is put into 'DFU Mode' and requires a different driver than used for normal connection and configuration.  The easiest way to install that driver is to download Zadig.  It's a driver management tool that runs as a simple .exe file, no installation is required. 
• Connect the flight control board in Betaflight (see above).  Once a connection has been verified, click disconnect and go to "Firmware Flasher".  Choose the latest hex file for RG_SSD_F3 and then "Load Firmware Online".  Once loaded, click "Flash Firmware".  This will put your board in DFU mode (solid blue LED), allowing it to be seen by Zadig so you can install the driver. 
• Open Zadig
• Choose Options > List All Devices
• Select STM32 BOOTLOADER in the device list (if instead you see STM32 Virtual Com Port you are not in DFU mode - don't replace the driver!)
• Choose WinUSB (v6.x.x.x) in the box on the right side of the green arrow
• Click Replace Driver
• Unplug the control board from the computer and restart the Betaflight configurator
• Click "Firmware Flasher" again and this time you should see the board in DFU mode in the top right corner after you attempt to flash.

For accurate VBAT readings, please set voltage scale on configuration page to 119 (from default 110)








SBUS or other serial rx



available – usually telemetry






onboard IR LEDs



Write a review

Please Login To Review This Product

Rotorgeeks © 2019
View Mobile / Standard