HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller FrSky

HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller FrSky
HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller FrSky HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller FrSky HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller FrSky
×
Brand: HappyModel
Product Code: 2E30024
Availability: Out Of Stock
Price: CAD$55.43
Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

An updated version of the all in one flight controller from HappyModel. It is a single board providing an F4 processor with MPU6000 gyro, OSD, built-in FrSKY receiver and four 5A ESCs.  We have attempted to capture and explain the changes to each revision below.  This is the latest revision still capable of running on 1S power.

 V2.0 changes:

  • 3S capable (FETs changed)
  • bind and boot buttons changed to larger size for convenience
  • main power pads changed to through-hole for better physical connection
Flight Controller
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1-3S battery input (DC 3.5-13V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • ESC MCU Upgraded to EFM8BB21
  • Frsky version Built-in SPI Frsky receiver with telemetry(D8 - recommended/D16 switchable)
  • Built-in Betaflight OSD (SPI Control)
  • Built-in Current meter sensor Max up to 28A
  • Current meter scale set to 1175
  • Built-in 5V 1A Buck / Boost with LC filter
  • Built-in voltage detection
  • BLHELI_S pass-through Ready
  • Multi Serial port support
  • Fully compatible with almost Brushless whoop drone
  • Weight:4.2g
Onboard 4in1 ESC
  • MCU upgraded to EFM8BB21
  • Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_50_REV16_7.Hex
  • Default protocol: DSHOT600


Package:

  • 1x Crazybee F4 PRO V2.0 flight controller
  • 3x Power cables
  • 1x set Shock absorbing rubber and screws

Firmware target: Frsky version  betaflight_4.0.0_CRAZYBEEF4FR.hex
Requires an older version of Betaflight configurator 10.4.0
Firmware updates here
FrSky manual here

Note from HappyModel:

Due to many complaints about upgrading the PH2.0 to XT30 causing the MOSFET to burn, it is now recommended to use an XT30 with a capacitor (ESR less than 0.2 ohm and a capacitance of more than 100uF).
With the Capacitor , you can use 3S 300~350mah battery for the Crazybee F4 PRO V2.0 and Crazybee F4 PRO V2.1 , and 2s 300~350mah battery for the Crazybee F4 PRO V1.0 And if you want to use the battery above 350mah , we recommend using a 220uF capacitor or above.

Please note that all warranty claims are handled and approved by Happy Model only.  If you have any issues please contact them here

Write a review

Please Login To Review This Product

Rotorgeeks © 2021
View Mobile / Standard