HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX

HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX
HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX HappyModel Crazybee F4 Pro V2.0 1-3S Brushless flight controller DSMX
×
Brand: HappyModel
Product Code: 2E30027
Availability: Out Of Stock
Price: USD$41.99
Qty:     - OR -   Add to Wish List
Add to Compare
0 reviews  0 reviews  |  Please Login To Review This Product

A further updated version of the all in one flight controller from HappyModel. It is a single board providing an F4 processor with MPU6000 gyro, OSD, built-in DSM2/X receiver and four 5A ESCs.  We have attempted to capture and explain the changes to each revision below.

 V2.0 changes

  • 3S capable (FETs changed)
  • bind and boot buttons changed to larger size for convenience
  • main power pads changed to through-hole for better physical connection
Flight Controller
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000(SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1-3S battery input (DC 3.5-13V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • ESC MCU Upgraded to EFM8BB21
  • DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver)
  • Dsm2/DSMX, Ibus protocol etc.
  • Built-in Betaflight OSD (SPI Control)
  • Built-in Current meter sensor Max up to 28A
  • Current meter scale set to 1175
  • Built-in 5V 1A Buck / Boost with LC filter
  • Built-in voltage detection
  • BLHELI_S pass-through Ready
  • Multi Serial port support
  • Fully compatible with almost Brushless whoop drone
  • Weight:4.2g
Onboard 4in1 ESC
  • MCU upgraded to EFM8BB21
  • Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_50_REV16_7.Hex
  • Default protocol: DSHOT600


Package:

  • 1x Crazybee F4 PRO V2.1 flight controller
  • 3x Power cables
  • 1x set Shock absorbing rubber and screws

Firmware updates here
Requires an older version of Betaflight configurator 10.4.0
DSMX manual here
Requires an older version of Betaflight configurator 10.4.0
 

Note from HappyModel:

Due to many complaints about upgrading the PH2.0 to XT30 causing the MOSFET to burn, it is now recommended to use an XT30 with a capacitor (ESR less than 0.2 ohm and a capacitance of more than 100uF).
With the Capacitor , you can use 3S 300~350mah battery for the Crazybee F4 PRO V2.0 and Crazybee F4 PRO V2.1 , and 2s 300~350mah battery for the Crazybee F4 PRO V1.0 And if you want to use the battery above 350mah , we recommend using a 220uF capacitor or above.

Please note that all warranty claims are handled and approved by Happy Model only.  If you have any issues please contact them here

Write a review

Please Login To Review This Product

Rotorgeeks © 2020
View Mobile / Standard